Ford Ecosport Owners and Service Manuals

Ford Ecosport: Exterior Lighting / Diagnosis and Testing - Fog Lamps

DTC Chart: BCM

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).

  DTC Description Action
B1046:11 Front Fog Lamp Control Switch: Circuit Short To Ground   GO to Pinpoint Test C
B1147:11 Left Front Fog Lamps: Circuit Short To Ground   GO to Pinpoint Test B
B1147:15 Left Front Fog Lamps: Circuit Short To Battery or Open
  • If the fog lamp is inoperative, GO to Pinpoint Test B
  • If the fog lamp is always on, GO to Pinpoint Test C
B1148:11 Right Front Fog Lamps: Circuit Short To Ground   GO to Pinpoint Test B
B1148:15 Right Front Fog Lamps: Circuit Short To Battery or Open
  • If the fog lamp is inoperative, GO to Pinpoint Test B
  • If the fog lamp is always on, GO to Pinpoint Test C
U1000:00 Solid State Driver Protection Active -Driver Disabled: No Sub Type Information The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The BCM cannot enable the output until the cause of the short is corrected. ADDRESS all other Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).
U3000:49 Control Module: Internal Electronic Failure The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. The cause of the excessive current draw MUST be corrected before a new BCM is installed. ADDRESS all other Diagnostic Trouble Codes (DTCs) first. After the cause of the concern is corrected, INSTALL a new BCM .
REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Removal and Installation).
For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).
All other BCM Diagnostic Trouble Codes (DTCs) -  
REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Diagnosis and Testing).

Symptom Chart

Symptom Chart: Fog Lamps

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).


  Symptom Chart


Condition Possible Sources Actions
A module does not respond to the diagnostic scan tool
  • Fuse
  • Wiring, terminals or connectors
  • Module
 
REFER to: Communications Network (418-00 Module Communications Network, Diagnosis and Testing).
Both front fog lamps are inoperative Refer to the Pinpoint Test   GO to Pinpoint Test A
An individual front fog lamp is inoperative Refer to the Pinpoint Test   GO to Pinpoint Test B
One or both front fog lamps are on continuously Refer to the Pinpoint Test   GO to Pinpoint Test C

Pinpoint Tests


PINPOINT TEST A: BOTH FRONT FOG LAMPS ARE INOPERATIVE

Refer to Wiring Diagrams Cell 86 for schematic and connector information.

Normal Operation and Fault Conditions

REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).

REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).

Possible Sources

  • Wiring, terminals or connectors
  • Headlamp switch
  • Headlamps concern
  • BCM

Visual Inspection and Pre-checks

  • Inspect the headlamp switch for damage.
A1 CHECK THE LOW BEAM OPERATION
  • Ignition ON.
  • Place the headlamp switch in the HEADLAMPS then the OFF position.

Do the low beams operate correctly?
Yes GO to A2
No
REFER to: Headlamps (417-01 Exterior Lighting, Diagnosis and Testing).

A2 CHECK THE HEADLAMP SWITCH
  • Ignition OFF.
  • Disconnect: Headlamp Switch C205.
  • Carry out the headlamp switch component test.
    Refer to Wiring Diagrams Cell 149 for schematic and connector information.

Does the headlamp switch pass the component test?
Yes GO to A4
No INSTALL a new headlamp switch.
REFER to: Headlamp Switch (417-01 Exterior Lighting, Removal and Installation).

A3 CHECK THE BCM (BODY CONTROL MODULE) FOG LAMP SWITCH INPUT CIRCUIT FOR AN OPEN
  • Ignition OFF.
  • Disconnect: BCM C2280D.
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C205-14   C2280D-55

Is the resistance less than 3 ohms?
Yes GO to A4
No REPAIR the circuit.

A4 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Disconnect and inspect all BCM and all related in-line connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM and all related in-line connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new BCM .
REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

PINPOINT TEST B: AN INDIVIDUAL FRONT FOG LAMP IS INOPERATIVE

Refer to Wiring Diagrams Cell 86 for schematic and connector information.

Normal Operation and Fault Conditions

REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).

REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
BCM B1147:11 Left Front Fog Lamps: Circuit Short To Ground A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the LH fog lamp output circuit.
BCM B1147:15 Left Front Fog Lamps: Circuit Short To Battery Or Open A continuous memory and on-demand DTC that sets when the BCM detects an open from the LH fog lamp output circuit.
BCM B1148:11 Right Front Fog Lamps: Circuit Short To Ground A continuous memory and on-demand DTC that sets when the BCM detects a short to ground from the RH fog lamp output circuit.
BCM B1148:15 Right Front Fog Lamps: Circuit Short To Battery Or Open A continuous memory and on-demand DTC that sets when the BCM detects an open from the RH fog lamp output circuit.
BCM U1000:00 Solid State Driver Protection Active -Driver Disabled: No Sub Type Information This DTC sets when the BCM has temporarily shut down the output driver. The module has temporarily disabled an output because an excessive current draw exists (such as a short to ground). The BCM cannot enable the output until the cause of the short is corrected, the Diagnostic Trouble Codes (DTCs) have been cleared and a successful self-test is run. For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).
BCM U3000:49 Control Module: Internal Electronic Failure This DTC sets when the BCM has permanently shut down the output driver. The module has permanently disabled an output because an excessive current draw fault (such as a short to ground) has exceeded the limits that the BCM can withstand. CORRECT the cause of the excessive current draw before installing a new BCM . For additional information on BCM Field Effect Transistor (FET) protection,
REFER to: Module Controlled Functions - System Operation and Component Description (419-10 Multifunction Electronic Modules, Description and Operation).

Possible Sources

  • Bulb
  • Wiring, terminals or connectors
  • BCM

Visual Inspection and Pre-checks

  • Inspect the bulbs and make sure they are OK.
B1 CHECK FOR VOLTAGE TO THE INOPERATIVE FOG LAMP
  • Ignition OFF.
  • Disconnect: Inoperative LH Fog Lamp C152 or RH Fog Lamp C162.
  • Ignition ON.
  • Place the headlamp switch in the PARKLAMPS position and engage the fog lamp switch.
  • Measure:
    Click to display connectors

      LH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C152-2   Ground

    Click to display connectors

      RH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C162-2   Ground

Is the voltage greater than 11 volts?
Yes GO to B3
No GO to B2

B2 REPEAT THE ON-DEMAND SELF-TEST AND CHECK FOR VOLTAGE TO THE FOG LAMP
  • Place the headlamp switch in the OFF position.
  • Using a diagnostic scan tool, perform the BCM self-test.
  • Clear the Diagnostic Trouble Codes (DTCs) and repeat the self-test (required to enable the lamp output driver if DTC U1000:00 is present).
  • Ignition OFF.
  • Ignition ON.
  • Place the headlamp switch in the PARKLAMPS position and engage the fog lamp switch.
  • Measure:
    Click to display connectors

      LH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C152-2   Ground

    Click to display connectors

      RH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C162-2   Ground

Is the voltage greater than 11 volts?
Yes INSTALL a new front fog lamp bulb.
REFER to: Front Fog Lamp Bulb (417-01 Exterior Lighting, Removal and Installation).
No GO to B4

B3 CHECK THE INOPERATIVE FOG LAMP GROUND CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C152-2   C152-1

    Click to display connectors

      RH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C162-2   C162-1

Is the voltage greater than 11 volts?
Yes INSTALL a new front fog lamp bulb.
REFER to: Front Fog Lamp Bulb (417-01 Exterior Lighting, Removal and Installation).
No REPAIR the circuit.

B4 CHECK FOG LAMP VOLTAGE SUPPLY CIRCUIT FOR A SHORT TO GROUND
  • Place the headlamp switch in the OFF position.
  • Ignition OFF.
  • Disconnect: BCM C2280E.
  • Measure:
    Click to display connectors

      LH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C152-2   Ground

    Click to display connectors

      RH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C162-2   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to B5
No REPAIR the circuit. After the repair:
If no Diagnostic Trouble Codes (DTCs) are present, TEST the system for normal operation.
If DTC U1000:00 is present, CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test (required to enable the lamp output driver if DTC U1000:00 is present).
If DTC U3000:49 is present, INSTALL a new BCM .
REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Removal and Installation).

B5 CHECK FOG LAMP VOLTAGE SUPPLY CIRCUIT FOR AN OPEN
  • Measure:
    Click to display connectors

      LH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C152-2   C2280E-6

    Click to display connectors

      RH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C162-2   C2280E-7

Is the resistance less than 3 ohms?
Yes GO to B6
No REPAIR the circuit.

B6 CHECK FOG LAMP FUSED SUPPLY CIRCUIT FOR VOLTAGE
  • Measure:
    Click to display connectors

      LH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C2280G-12   Ground

    Click to display connectors

      RH Fog Lamp


    Positive Lead Measurement / Action Negative Lead
      C2280G-5   Ground

Is the voltage greater than 11 volts?
Yes GO to B7
No REPAIR the circuit.

B7 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Disconnect and inspect all BCM and all related in-line connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM and all related in-line connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new BCM .
REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.

PINPOINT TEST C: ONE OR BOTH THE FRONT FOG LAMPS ARE ON CONTINUOUSLY

Refer to Wiring Diagrams Cell 86 for schematic and connector information.

Normal Operation and Fault Conditions

REFER to: Exterior Lighting - Overview (417-01 Exterior Lighting, Description and Operation).

REFER to: Exterior Lighting - System Operation and Component Description (417-01 Exterior Lighting, Description and Operation).

DTC Fault Trigger Conditions

DTC Description Fault Trigger Condition
BCM B1046:11 Front Fog Lamp Control Switch: Circuit Short To Ground A continuous and on-demand DTC that sets when the BCM detects a short to ground on the headlamp switch input circuits.
BCM B1147:15 Left Front Fog Lamps: Circuit Short To Battery Or Open A continuous memory and on-demand DTC that sets when the BCM detects an open from the LH fog lamp output circuit.
BCM B1148:15 Right Front Fog Lamps: Circuit Short To Battery Or Open A continuous and on-demand DTC that sets when the BCM detects a short to voltage from the RH fog lamp beam output circuit.

Possible Sources

  • Wiring, terminals or connectors
  • Headlamp switch
  • BCM

Visual Inspection and Pre-checks

  • Inspect the headlamp switch for damage.
C1 CHECK THE HEADLAMP SWITCH
  • Ignition OFF.
  • Disconnect: Headlamp Switch C205.
  • Carry out the headlamp switch component test.
    Refer to Wiring Diagrams Cell 149 for schematic and connector information.

Does the headlamp switch pass the component test?
Yes GO to C2
No INSTALL a new headlamp switch.
REFER to: Headlamp Switch (417-01 Exterior Lighting, Removal and Installation).

C2 CHECK THE FOG LAMP VOLTAGE SUPPLY CIRCUITS FOR A SHORT TO VOLTAGE
  • Ignition OFF.
  • Disconnect: BCM C2280E.
  • Ignition ON.

Do the fog lamps continue to illuminate?
Yes GO to C3
No REPAIR the circuits.

C3 CHECK THE BCM (BODY CONTROL MODULE) FOG LAMP SWITCH INPUT CIRCUIT FOR A SHORT TO GROUND
  • Ignition OFF.
  • Disconnect: BCM C2280D.
  • Measure:
    Click to display connectors
    Positive Lead Measurement / Action Negative Lead
      C205-14   Ground

Is the resistance greater than 10,000 ohms?
Yes GO to C4
No REPAIR the circuit.

C4 CHECK FOR CORRECT BCM (BODY CONTROL MODULE) OPERATION
  • Disconnect and inspect all BCM and all related in-line connectors.
  • Repair:
    • corrosion (install new connector or terminals – clean module pins)
    • damaged or bent pins – install new terminals/pins
    • pushed-out pins – install new pins as necessary
  • Reconnect the BCM and all related in-line connectors. Make sure they seat and latch correctly.
  • Operate the system and determine if the concern is still present.

Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new BCM .
REFER to: Body Control Module (BCM) (419-10 Multifunction Electronic Modules, Removal and Installation).
No The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.


    Diagnosis and Testing - Daytime Running Lamps (DRL)

    DTC Chart: BCM Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation)...

    Diagnosis and Testing - Headlamps

    General Equipment Ford diagnostic equipment DTC Chart: BCM Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices...

    Other information:

    Ford Ecosport 2014-2024 Service and Repair Manual: Removal and Installation - Rear Door Glass Top Run


    Removal NOTE: LH side shown, RH side similar. NOTE: Removal steps in this procedure may contain installation details. Remove the rear door window control switch. Refer to: Rear Door Window Control Switch (501-11 Glass, Frames and Mechanisms, Removal and Installation)...

    Ford Ecosport 2014-2024 Service and Repair Manual: General Procedures - Brake Shift Interlock Actuator Manual Override


    Special Tool(s) / General Equipment Interior Trim Remover Activation Set the ignition switch to the OFF position and apply the parking brake. Remove the selector lever bezel trim ring...

    Categories

    Disassembly - Engine

    Special Tool(s) / General Equipment

    205-153 (T80T-4000-W)
    Handle 303-103 (T74P-6375-A)
    Holding Tool, Flywheel
    T74P-77000-A
    TKIT-2009TC-F 303-1247
    VCT Spark Plug Tube Seal Remover and Installer
    TKIT-2006UF-FLM
    TKIT-2006UF-ROW 303-15

    read more

    Copyright © 2024 www.foecosport2.com