Ford Ecosport: Electronic Engine Controls - 2.0L Duratec-HE (129kW/175PS) / Diagnosis and Testing - Engine Starting Control System

Ford Ecosport 2014-2024 Service and Repair Manual / Engine / Electronic Engine Controls - 2.0L Duratec-HE (129kW/175PS) / Diagnosis and Testing - Engine Starting Control System

Diagnostic Trouble Code (DTC) Chart

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).

Module	DTC	Description	Action
PCM	P164C:00	Internal Control Module Start-Stop Performance: No Sub Type Information	GO to Pinpoint Test AA

Global Customer Symptom Code (GCSC) Chart

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to: Diagnostic Methods (100-00 General Information, Description and Operation).

Symptom	Action
Start/Run/Move > Starting > Cranks Won't Start > Always	GO to Pinpoint Test A
Start/Run/Move > Starting > Hard Start/Long Crank > Always	GO to Pinpoint Test A
Start/Run/Move > Starting > Auto-Start-Stop > Inoperative	GO to Pinpoint Test AA

Pinpoint Tests

PINPOINT TEST A: NO START

Introduction

WARNING: Do not smoke, carry lighted tobacco or have an open flame of any type when working on or near any fuel-related component. Highly flammable mixtures may be present and may be ignited. Failure to follow these instructions may result in serious personal injury.

Normal Operation and Fault Conditions

Refer to the DTC Fault Trigger Conditions.

Possible Sources

Spark (as related to electronic engine control)
PCM (12A650)

PINPOINT TEST AA: AUTO START STOP

Introduction

Normal Operation and Fault Conditions

Refer to the DTC Fault Trigger Conditions.

DTC Fault Trigger Conditions

DTC	Description	Fault Trigger Condition
PCM P164C:00	Internal Control Module Start-Stop Performance: No Sub Type Information	Sets when an error occurs in the PCM . This DTC may be accompanied by other Diagnostic Trouble Codes (DTCs). Check for other Diagnostic Trouble Codes (DTCs) and diagnose those first. If no Diagnostic Trouble Codes (DTCs) are present, continue to follow diagnosis for this DTC .

Possible Sources

Aftermarket performance products
Module programming error
PCM configuration
PCM (12A650)

Diagnosis and Testing - Electronic Engine Controls

Diagnostic Trouble Code (DTC) Chart Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods (100-00 General Information, Description and Operation)...

Diagnosis and Testing - Powertrain Control Module (PCM) Input and Output Controls

Other information:

Ford Ecosport 2014-2024 Service and Repair Manual: Diagnosis and Testing - Pinpoint Test - DTC: AV, Vehicles With: Rear Seat Side Airbag

U0100:87 Normal Operation and Fault Conditions The BECMB uses information contained in messages from the PCM sent on the HS-CAN1 . DTC Fault Trigger Conditions DTC Description Fault Trigger Conditions U0100:87 Lost Communication with ECM/PCM “A”: Missing Message ..

Ford Ecosport 2014-2024 Service and Repair Manual: General Procedures - Headlamp Adjustment

Adjustment NOTE: If the flash video link does not load or is incompatible with your browser, a .wmv version of the video can be accessed at: http://www.fordservicecontent.com/Ford_Content/videos/FusionHeadlampAdj2.wmv Click on the link above to view video. Click here to view a video version of this procedure. All headlamp types NOTE: ..

Removal and Installation - Wheel Knuckle Bushing

Special Tool(s) / General Equipment

Hydraulic Press

Removal

NOTE: Removal steps in this procedure may contain installation details.

Remove the wheel knuckle.
Refer to: Wheel Knuckle - Vehicles With: Rear Drum Brakes (204-02B Rear Suspension - AWD, Removal and Installation).
Remove the rear toe adjustment retainers and remove the wheel knuckle mounting bracket.
Torque:
Stage 1: 177 lb.in (20 Nm)
Stage 2: 76 lb.ft (103 Nm)