Ford Ecosport Owners and Service Manuals

Ford Ecosport: Handles, Locks, Latches and Entry Systems / Removal and Installation - Hood Latch Release Cable

Ford Ecosport 2014-2025 Service and Repair Manual / Body and Paint / Handles, Locks, Latches and Entry Systems / Removal and Installation - Hood Latch Release Cable

Removal

  1. Remove the air cleaner.
    Refer to: Air Cleaner (303-12A Intake Air Distribution and Filtering - 1.0L EcoBoost (92kW/125PS), Removal and Installation).
    Refer to: Air Cleaner (303-12B Intake Air Distribution and Filtering - 1.5L Duratec (90kW/120PS) – I3, Removal and Installation).
    Refer to: Air Cleaner (303-12C Intake Air Distribution and Filtering - 2.0L Duratec-HE (129kW/175PS), Removal and Installation).
  1. Remove the battery tray.
    Refer to: Battery Tray (414-01 Battery, Mounting and Cables, Removal and Installation).
  1. Remove the hood latch release handle.
    Refer to: Hood Latch Release Handle (501-14 Handles, Locks, Latches and Entry Systems, Removal and Installation).

  1. Disconnect the primary hood latch release cable.
    1. Disconnect the primary hood latch release cable from the mounting bracket.
    1. Remove the primary hood latch release cable eyelet from the hood latch.
  1. Route the hood latch release cable and grommet into the engine compartment.
  1. Route the hood latch release cable and release cable routing clip.
  1. Release cable routing clip and remove the hood latch release cable.

Installation

  1. Route the hood latch release cable and grommet into the engine compartment.
  1. Route the hood latch release cable and secure cable routing clip.
  1. Route the hood latch release cable and secure cable routing clip.

  1. Connect the primary hood latch release cable.
    1. Install the primary hood latch release cable eyelet to the hood latch.
    1. Connect the primary hood latch release cable to the mounting bracket.
  1. Install the hood latch release handle.
    Refer to: Hood Latch Release Handle (501-14 Handles, Locks, Latches and Entry Systems, Removal and Installation).
  1. Install the battery tray.
    Refer to: Battery Tray (414-01 Battery, Mounting and Cables, Removal and Installation).
  1. Install the air cleaner.
    Refer to: Air Cleaner (303-12A Intake Air Distribution and Filtering - 1.0L EcoBoost (92kW/125PS), Removal and Installation).
    Refer to: Air Cleaner (303-12B Intake Air Distribution and Filtering - 1.5L Duratec (90kW/120PS) – I3, Removal and Installation).
    Refer to: Air Cleaner (303-12C Intake Air Distribution and Filtering - 2.0L Duratec-HE (129kW/175PS), Removal and Installation).

    Removal and Installation - Hood Latch

    Removal NOTE: Removal steps in this procedure may contain installation details. If equipped. Disconnect the hood ajar switch electrical connector...

    Removal and Installation - Hood Latch Release Handle

    Removal Remove the LH instrument panel trim cover. Remove the hood latch release handle...

    Other information:

    Ford Ecosport 2014-2025 Service and Repair Manual: Removal and Installation - Rear Fender Splash Shield


    Removal NOTE: Removal steps in this procedure may contain installation details. NOTE: LH side shown, RH side similar. Disengage the pushpin and the clips, position aside the rocker panel moulding. Remove the pushpin and the retainers...

    Ford Ecosport 2014-2025 Service and Repair Manual: General Procedures - Evaporative Emission System Leak Test


    Activation Phase 1 - Leak Verification Run the EVAP Test with the scan tool. NOTE: Some small leaks may not be detected using the EVAP Test. If the system has passed the test but a leak is still suspected, then proceed to Phase 2...

    Categories

    Removal and Installation - Rear Halfshaft Seal

    Special Tool(s) / General Equipment

    205-153 (T80T-4000-W)
    Handle 205-990
    Installer, Axle Seal
    TKIT-2012A-FL
    TKIT-2012A-ROW

    read more

    Copyright © 2025 www.foecosport2.com