Ford Ecosport: Evaporative Emissions - 2.0L Duratec-HE (129kW/175PS) / Removal and Installation - Evaporative Emission Canister

Ford Ecosport 2014-2025 Service and Repair Manual / Engine / Evaporative Emissions - 2.0L Duratec-HE (129kW/175PS) / Removal and Installation - Evaporative Emission Canister

Removal

WARNING: Do not smoke, carry lighted tobacco or have an open flame of any type when working on or near any fuel-related component. Highly flammable mixtures may be present and may be ignited. Failure to follow these instructions may result in serious personal injury.

WARNING: Do not carry personal electronic devices such as cell phones, pagers or audio equipment of any type when working on or near any fuel-related component. Highly flammable mixtures may be present and may be ignited. Failure to follow these instructions may result in serious personal injury.

WARNING: Always disconnect the battery ground cable at the battery when working on an evaporative emission (EVAP) system or fuel-related component. Highly flammable mixtures may be present and may be ignited. Failure to follow these instructions may result in serious personal injury.

NOTE: Removal steps in this procedure may contain installation details.

Remove the EVAP blocking valve.
Refer to: Evaporative Emission Blocking Valve (303-13A Evaporative Emissions - 1.0L EcoBoost (92kW/125PS), Removal and Installation).

- Disconnect the EVAP solenoid electrical connector and position aside the wiring harness.
- Detach the wiring harness retainers and position aside the wiring harness.
- Remove the adaptor and position aside the fuel vapour vent hose.

- Disconnect the quick connector and position aside the fuel vapour return hose.
  Refer to: Quick Release Coupling (310-00A Fuel System - General Information - 1.0L EcoBoost (92kW/125PS), General Procedures).
- Remove the nuts, screws and EVAP canister assembly.
  Torque: 62 lb.in (7 Nm)

- Disconnect the quick connector.
  Refer to: Quick Release Coupling (310-00A Fuel System - General Information - 1.0L EcoBoost (92kW/125PS), General Procedures).
- Remove the bolts and EVAP bracket.
  Torque: 62 lb.in (7 Nm)

Installation

To install, reverse the removal procedure.

Removal and Installation - Evaporative Emission Blocking Valve

Removal NOTE: The evaporative emission blocking valve is serviced with the fuel tank pressure sensor and tube. With the vehicle in NEUTRAL, position it on a hoist...

Removal and Installation - Evaporative Emission Canister Purge Valve

Removal WARNING: Do not smoke, carry lighted tobacco or have an open flame of any type when working on or near any fuel-related component...

Other information:

Ford Ecosport 2014-2025 Service and Repair Manual: Description and Operation - Steering Wheel and Column Electrical Components - Overview

Steering Column Switches Overview The steering column switches are located on and around the steering column. They enable the driver to control various vehicle functions while remaining focused on driving. The steering column switches consist of: Left multifunction switch - mounted on the left side of the SCCM and is used: to control the turn signals, low/high beam selectio..

Ford Ecosport 2014-2025 Service and Repair Manual: General Procedures - Air Conditioning (A/C) System Recovery, Evacuation and Charging - Vehicles With: R1234YF Refrigerant

Special Tool(s) / General Equipment Air Conditioning Service Unit Refrigerant Identification Equipment Recovery NOTICE: Use an A/C refrigerant analyzer before recovering any of the vehicle's A/C refrigerant. Failure to do so puts the shop's bulk refrigerant at risk of contamination. If the vehicle's A/C refrigerant is contaminated, refer the customer to the se..

Removal and Installation - Front Stabilizer Bar

Special Tool(s) / General Equipment

Tie Rod End Remover Transmission Jack

Removal

NOTICE: Suspension fasteners are critical parts that affect the performance of vital components and systems. Failure of these fasteners may result in major service expense. Use the same or equivalent parts if replacement is necessary. Do not use a replacement part of lesser quality or substitute design. Tighten fasteners as specified.

NOTE: Removal steps in this procedure may contain installation details.

NOTICE: Disconnect the b