Ford Ecosport Owners and Service Manuals

Ford Ecosport: Supplemental Restraint System / Diagnosis and Testing - Pinpoint Test - DTC: AI, Vehicles With: Rear Seat Side Airbag

Ford Ecosport 2014-2024 Service and Repair Manual / Body and Paint / Supplemental Restraint System / Diagnosis and Testing - Pinpoint Test - DTC: AI, Vehicles With: Rear Seat Side Airbag

U0112:00

Normal Operation and Fault Conditions

The RCM uses information contained in messages from the BECMB sent on the HS-CAN2 .


  DTC Fault Trigger Conditions


  DTC Description Fault Trigger Conditions
U0112:00 Lost Communication With Battery Energy Control Module "B": No Sub Type Information This DTC sets if the RCM does not receive an expected message from the BECMB .

Possible Sources

  • Network traffic
  • BECMB
  • RCM

PINPOINT TEST A: U0112:00
  WARNING: Do not handle, move or change the original horizontal mounting position of the Restraints Control Module (RCM) while the Restraints Control Module (RCM) is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy® and cause serious personal injury or death.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: SRS components should only be disconnected or reconnected when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS .
NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
A1 CHECK THE COMMUNICATION NETWORK
  •   WARNING: Before beginning any service procedure in this section, refer to Safety Warnings in section 100-00 General Information. Failure to follow this instruction may result in serious personal injury.
  • Ignition ON.
  • Using a diagnostic scan tool, carry out a network test.

Does the BECMB pass the network test?
Yes GO to A2
No To diagnose no communication with the BECMB ,
REFER to: Communications Network (418-00) .

A2 CHECK THE RCM (RESTRAINTS CONTROL MODULE) CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODES (CMDTCS)
  • Using a diagnostic scan tool, perform RCM self-test.
  • Using a diagnostic scan tool, clear RCM Diagnostic Trouble Codes (DTCs).
  • Wait 10 seconds.
  • Using a diagnostic scan tool, perform RCM self-test.

Is DTC U0112:00 retrieved again?
Yes GO to A3
No The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

A3 RETRIEVE THE RECORDED DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE RCM (RESTRAINTS CONTROL MODULE) SELF-TEST
  • Check the recorded Diagnostic Trouble Codes (DTCs) from the RCM self-test.

Is DTC U3003:16 or U3003:17 recorded?
Yes
No CHECK OASIS for any applicable service articles: TSB , GSB , SSM or FSA . If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new BECMB .
REFER to: Battery Energy Control Module B (BECMB) (501-20B Supplemental Restraint System, Removal and Installation). REPEAT the RCM self-test. If DTC U0112:00 returns, INSTALL a new RCM .
REFER to: Restraints Control Module (RCM) (501-20B Supplemental Restraint System, Removal and Installation).


    Diagnosis and Testing - Pinpoint Test - DTC: AH, Vehicles With: Rear Seat Side Airbag

    U..

    Diagnosis and Testing - Pinpoint Test - DTC: AJ, Vehicles With: Rear Seat Side Airbag

    U0413:56 Normal Operation and Fault Conditions The RCM uses information contained in messages from the BECMB sent on the HS-CAN2 .   DTC Fault Trigger Conditions   DTC Description Fault Trigger Conditions U0413:56 Lost Communication with Body Control Module: No Sub Type Informat..

    Other information:

    Ford Ecosport 2014-2024 Service and Repair Manual: General Procedures - Selector Lever Cable Adjustment - 6-Speed Automatic Transmission – 6F35


    Adjustment Apply the parking brake. Position the selector lever in D . Remove the air cleaner. Refer to: Air Cleaner (303-12C Intake Air Distribution and Filtering - 2.0L Duratec-HE (129kW/175PS), Removal and Installation). Disconnect the selector lever cable..

    Ford Ecosport 2014-2024 Service and Repair Manual: General Procedures - Heater Core Leak Check - Vehicles With: R1234YF Refrigerant


    Inspection NOTE: A coolant leak in the heater hose could follow the heater core tube to the heater core and appear as a leak in the heater core. Inspect for evidence of coolant leakage at the heater hose to heater core attachments. NOTE: Spring-type clamps are installed as original equipment. Installation and overtightening of nonspecified clamps can ..

    Categories

    Removal and Installation - Steering Column Shaft

    Removal

    NOTE: Removal steps in this procedure may contain installation details.

    NOTICE: Do not allow the steering column to rotate while the steering column shaft is disconnected or damage to the steering column internal sensor may result.

    NOTE: Use a steering wheel holding device (such as Hunter® 28-75-1 or equivalent)

    Hold the steering wheel in the straight-ahead position.

    read more

    Copyright © 2024 www.foecosport2.com